In the process of equipment operation, the loss of the machine is very serious. Annual depreciation maintenance is a considerable part of the company's factory expenses. Now the technical maintenance workers, from the perspective of talent recruitment, still have a certain lack. For some people, basic knowledge of guide screw maintenance can help them find a good job.

　　1、滾珠絲杠制造商要搞清楚，是什么原因導致了滾珠的掉落。

　　1. The ball screw manufacturer should find out what causes the ball to fall.

　　2、將螺絲對拆下，軸承座、軸承全部拆下;找一個螺絲對下來，軸承，軸承，全部下來;(外殼外徑與絲杠螺紋底徑相同;殼體內徑與絲杠支撐軸外徑相同;外殼的外徑與絲杠螺紋的底徑相同。(同直徑)，將套管套在絲杠支撐軸上，將絲杠螺母擰到套管上;當襯套完全轉向襯套時，拔出襯套和螺帽?；瑒咏z杠螺母直到它完全旋轉到襯套上。拆下襯套和絲杠螺母。在襯套的一端，讓螺母接觸到球的一半

　　2. Remove the screw pair, remove the bearing seat and bearing; find a screw pair, remove the bearing and bearing; (the outer diameter of the shell is the same as the bottom diameter of the screw thread; the inner diameter of the shell is the same as the outer diameter of the screw support shaft; the outer diameter of the shell is the same as the bottom diameter of the screw thread. (the same diameter), put the sleeve on the screw support shaft, and screw the screw nut onto the sleeve; when the sleeve turns completely to the sleeve, pull out the sleeve and nut. Slide the lead screw nut until it completely rotates onto the bushing. Remove the bushing and the lead screw nut. At one end of the bushing, let the nut touch half of the ball

　　套管的一端,使半圈滾珠螺母(必須注意,出來,或者球都會脫落),用小棒或者線,出來,或球都會脫落),用小棒或者線,球),用細小的調整桿的位置或線,露出一個或更多的球的位置,然后調節落球的位置填寫,顯示的位置一個或更多的球軸承,(這一步很重要,更好有滾珠絲杠副裝配經驗);填寫這一步很重要，更好有滾珠絲杠副裝配的經驗做)，然后將套筒放在絲杠軸上;之后，把螺帽擰到絲杠上。然后，將套管套在絲杠支撐軸上;之后，把螺帽擰到絲杠上。

　　One end of the bushing makes the half circle ball nut (which must be noticed, or the ball will fall off), use a stick or thread, or the ball will fall off, use a small stick or line, ball, use a small adjusting rod position or line to reveal the position of one or more balls, then adjust the position of the falling ball to fill out the position of one or more ball bearings. (this step is very important. It is better to have assembly experience of ball screw pair); it is important to fill in this step, preferably with assembly experience of ball screw pair), and then place the sleeve on the screw shaft; after that, screw the nut onto the screw. Then, put the sleeve on the screw support shaft, and then screw the nut onto the screw.

　　3、滾珠螺桿修復好,重新安裝螺絲,需要找到一個好的連接部分螺釘對修復好后,重新安裝螺釘,包括定位精度的準確性,定位精度,等等,如正直、對齊、包括定位精度的準確性,定位精度,等等,如直線度、同軸度、平行度、直徑跳,更后什么的。說簡單，其實挺麻煩的，需要小心忍著路跳，到底跳的是什么。說起來容易，但實際上工作量很大。有經驗的機械師或鉗工可以做這件事。一個有經驗的機械師或鉗工可以做到這一點。

　　3. After the ball screw is repaired and the screw is reinstalled, it is necessary to find a good connecting part of the screw pair, and then reinstall the screw, including the accuracy of positioning accuracy, positioning accuracy, etc., such as straightness, coaxiality, parallelism, diameter jump, and the last one. In short, it's really troublesome. You need to be careful and bear the road jump. What is it. It's easy to say, but it's a lot of work. An experienced mechanic or fitter can do it. An experienced mechanic or fitter can do this.

　　4、滾珠螺桿有多種形式,更常見的是使用返回,返回導螺桿有多種形式,管兩個,如果不是把螺絲螺母,不失去球管兩種,如果不是不失滾珠絲杠螺母擰出,如果沒有把螺母,出球,明返回或返回管壞了,沒有把螺絲和球了,返回或回水管壞了,需要改變包裝。如果沒有損壞，你就得換新的。如果沒有損壞，則使用鋰潤滑脂將球粘在每個單獨的滾道上，每個單獨的滾道上，然后用與普通螺母相同的方式將螺母旋回圓形滾道。關鍵是在開始時瞄準，一旦球滑出，就重新開始。再試一次。小心不要在非圓形(螺旋坑)上嘗試超過兩次。

　　4. There are many forms of ball screw, the most common one is to use return. There are many forms of return guide screw. There are two pipes. If the screw nut is not screwed out, there are two kinds of ball pipe. If the ball screw nut is not screwed out, if the nut is not screwed out, the return or return pipe is broken, the screw and ball are not screwed out, the return or return pipe is broken, and the packaging needs to be changed. If there is no damage, you have to replace it. If there is no damage, use lithium grease to stick the ball on each separate raceway, each separate raceway, and then turn the nut back to the circular raceway in the same way as the ordinary nut. The key is to aim at the beginning and start again as soon as the ball slips out. do it again. Be careful not to try more than twice on a non-circular (spiral pit).

　　以上是導軌絲杠滾珠的保養方法。我希望能給你技術上的幫助。

　　The above is the maintenance method of guide screw ball. I hope I can give you technical help.